User Tools
sccl:usage
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
sccl:usage [2015-05-13 11:25] uls [sccl_get_aktnode] |
sccl:usage [2015-07-23 15:56] (current) uls [sccl_get_aktnode] |
||
|---|---|---|---|
| Line 40: | Line 40: | ||
| === sccl_disable_node === | === sccl_disable_node === | ||
| === sccl_dist_config === | === sccl_dist_config === | ||
| + | |||
| + | sccl_dist_config [-m] [-x <excludenode>] [-n <onlynode>] [files ...] | ||
| + | |||
| + | Distribute the cluster-relvant files to all other nodes. | ||
| + | Normally, you do not specify any files explicitly. | ||
| + | |||
| + | sccl_dist_config | ||
| + | |||
| + | Mainly the files: | ||
| + | etc/sccl/sccl.conf | ||
| + | etc/sccl/adminpwd.dat | ||
| + | etc/sccl/userpwd.dat | ||
| + | etc/sccl/packages.conf | ||
| + | etc/sccl/resources.conf | ||
| + | etc/sccl/scripts/ | ||
| + | These files will overwrite any existing files on the destination nodes:!: | ||
| + | |||
| + | Special action: define <other_node> also as master. | ||
| + | |||
| + | sccl_dist_config -m -n <other_node> | ||
| + | | ||
| + | Remember: only a master node can add more nodes | ||
| + | |||
| + | ----- | ||
| === sccl_enable === | === sccl_enable === | ||
| === sccl_enable_node === | === sccl_enable_node === | ||
| === sccl_get_aktnode === | === sccl_get_aktnode === | ||
| - | Findet den/die aktiven Clusterknoten zu einem Clusterpaket. | + | Find the active cluster node(s) for a cluster package. |
| - | $ /usr/local/sccl/sccl_get_aktnode <package> | + | |
| + | $ sccl_get_aktnode <package> | ||
| { [<node1> [<node2>]...] | 0 } | { [<node1> [<node2>]...] | 0 } | ||
| - | Es werden die Namen der Clusterknoten ausgegeben, auf denen das <package> aktiv ist. Ist das <package> auf keinem Clusterknoten aktiv, dann wird | + | All names of all cluster nodes are listet, on which the <package> is active. |
| - | 0 | + | If the <package> is not active on any cluster node, the output is: |
| - | ausgegeben. | + | <file> |
| + | 0 | ||
| + | </file> | ||
| - | Beispiel: | + | Example: |
| - | $ /usr/local/sccl/sccl_get_aktnode package3 | + | $ sccl_get_aktnode package3 |
| clnode1 clnode2 | clnode1 clnode2 | ||
| + | The package package3 is active on the cluster nodes clnode1 and clnode2. | ||
| ----- | ----- | ||
| === sccl_list_cluster === | === sccl_list_cluster === | ||
sccl/usage.1431509144.txt.gz · Last modified: 2015-05-13 11:25 by uls
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: GNU Free Documentation License 1.3
